HTD 8M-50 Timing Pulley
8M curvilinear synchronous timing pulley, 8M-50 series. Select tooth count, belt width and shaft interface from the catalogue table or approved drawing.
HTD 8M-50 Timing Pulley Configuration Overview
8M-50 HTD Timing Pulley is a 8 mm pitch synchronous pulley family with a nominal belt-face reference of 50 in the catalogue naming system. This page treats the series as a configurable industrial component rather than a single fixed SKU. Tooth count changes pulley diameter and may also change hub, flange, material or mounting details, so the order must be tied to a specific catalogue row or an approved drawing.
For procurement, begin with the complete belt designation and confirm that the mating belt uses the same HTD 8M profile. Pitch alone is not a safe interchange rule for every curvilinear belt family. After profile confirmation, select tooth count and working width, then review the shaft interface, hub projection, flange arrangement and available material. This sequence reduces the common replacement error of matching only outside diameter while overlooking the tooth system or mounting geometry.
The straight-bore construction shown for this family is intended for positive synchronous power transmission. Typical enquiries come from machine tools, conveyors and higher-duty industrial motion. Actual suitability depends on speed, transmitted load, center distance, belt construction, alignment, environment and shaft support. Those duty inputs should be supplied for a new drive or when an existing machine has recurring belt-tracking or wear problems.
8M-50 Construction and Shaft Interface
8M-50 belongs to the 8M HTD family and this page covers straight-bore construction. The catalogue table on this page spans 22–192 teeth. Construction codes visible in the table include 2F, 7F, 7, 8. Use the exact product code with the tooth count because the hub/flange arrangement can change inside one width series.
The width code 50 identifies this catalogue family; it is not a substitute for checking the mating belt marking and the dimension drawing. For replacement work, preserve the installed belt line and measure the shaft-side geometry before deciding that a row with the correct teeth is a mechanical substitute.
Read the 8M-50 Dimension View Before the Table
The dimension view explains how symbols such as Dp, De, Df, Dm, Di, F, L and bore-related fields relate to the construction drawing. Use the drawing and the same product row together; do not transfer a dimension from another construction type simply because the pitch and tooth count match.
For 8M-50, record the values that control installation—working face, hub projection, flange envelope and shaft connection—against a stable machine datum. If a finished bore, keyway or tolerance is not defined by the catalogue row, add it on the RFQ or controlled drawing instead of assuming a universal value.
8M-50 Technical Specification Table
The following values are transcribed from the selected timing-pulley catalogue for this series. Use the code and tooth count together when requesting a quotation. Dimensions are catalogue values; final shaft fit, keyway, surface finish and inspection requirements should be stated on the RFQ or drawing.
| Code | Type | Teeth | Dp | De | Df | Dm | Di | F | L | d | Flange | Approx. kg |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 22-8M-50 | 2F | 22 | 56,02 | 54,65 | 60 | 43 | – | 60 | 70 | 12 | 308 | 1,10 |
| 24-8M-50 | 2F | 24 | 61,11 | 59,74 | 66 | 45 | – | 60 | 70 | 12 | 310 | 1,30 |
| 26-8M-50 | 2F | 26 | 66,21 | 64,84 | 71 | 48 | – | 60 | 70 | 12 | 311 | 1,60 |
| 28-8M-50 | 2F | 28 | 71,30 | 70,08 | 75 | 50 | – | 60 | 70 | 14 | 312 | 1,70 |
| 30-8M-50 | 2F | 30 | 76,39 | 75,13 | 83 | 55 | – | 60 | 70 | 14 | 314 | 2,00 |
| 32-8M-50 | 2F | 32 | 81,49 | 80,16 | 87 | 60 | – | 60 | 70 | 14 | 315 | 2,35 |
| 34-8M-50 | 2F | 34 | 86,58 | 85,21 | 91 | 66 | – | 60 | 70 | 14 | 316 | 2,80 |
| 36-8M-50 | 2F | 36 | 91,67 | 90,30 | 98,5 | 70 | – | 60 | 70 | 14 | 319 | 3,10 |
| 38-8M-50 | 2F | 38 | 96,77 | 95,39 | 103 | 75 | – | 60 | 70 | 14 | 320 | 3,30 |
| 40-8M-50 | 2F | 40 | 101,86 | 100,49 | 106 | 75 | – | 60 | 70 | 14 | 321 | 3,60 |
| 44-8M-50 | 2F | 44 | 112,05 | 110,67 | 119 | 75 | – | 60 | 70 | 14 | 325 | 4,40 |
| 48-8M-50 | 2F | 48 | 122,23 | 120,86 | 127 | 75 | – | 60 | 70 | 14 | 327 | 5,00 |
| 56-8M-50 | 7F | 56 | 142,60 | 141,23 | 148 | 90 | 116 | 60 | 60 | 18 | 333 | 5,68 |
| 64-8M-50 | 7F | 64 | 162,97 | 161,60 | 168 | 100 | 137 | 60 | 60 | 18 | 338 | 6,93 |
| 72-8M-50 | 7F | 72 | 183,35 | 181,97 | 192 | 100 | 158 | 60 | 60 | 18 | 340 | 7,95 |
| 80-8M-50 | 7 | 80 | 203,72 | 202,35 | – | 110 | 180 | 60 | 60 | 18 | – | 7,96 |
| 90-8M-50 | 7 | 90 | 229,18 | 227,81 | – | 110 | 204 | 60 | 60 | 18 | – | 9,20 |
| 112-8M-50 | 8 | 112 | 285,21 | 283,83 | – | 110 | 254 | 60 | 60 | 18 | – | 12,16 |
| 144-8M-50 | 8 | 144 | 366,69 | 365,32 | – | 110 | 336 | 60 | 60 | 20 | – | 15,68 |
| 168-8M-50 | 8 | 168 | 427,81 | 426,44 | – | 120 | 400 | 60 | 60 | 20 | – | 18,99 |
| 192-8M-50 | 8 | 192 | 488,92 | 487,55 | – | 130 | 460 | 60 | 60 | 20 | – | 24,09 |
Where the 8M-50 Family Fits
8M-50 is part of the 8M family used for industrial synchronous drives where tooth count, construction type, bore or bush and axial installation space should be reviewed together. Application suitability is not determined by pitch alone. A new drive still needs the required speed relationship, load or torque basis, center distance, environment and service conditions before the pulley row can be finalized.
For a replacement, the safest starting point is the existing belt/profile identity plus the original tooth count. Changing the tooth count changes pitch diameter and drive ratio, while changing the mounting construction can move the belt line or alter removal access.
Material and Construction Choices for 8M-50
Use the material and construction shown for the exact 8M-50 product code or approved drawing. Do not identify pulley material from color, surface appearance or a photograph. Where a project requests a different material, finish, hub, flange or shaft feature, treat that as a custom requirement and review its effect on dimensions and inspection before quotation.
Within the 22–192 teeth range, construction codes can vary. That variation is why the product code, tooth count and construction view should remain together in the order record.
Installation Checks for 8M-50
Before installation, compare the new pulley with the released 8M-50 row or drawing. Verify the shaft connection, axial position, flange condition and belt line before tension is applied. The belt should enter the pulley without being forced sideways by a misaligned shaft, displaced hub or incorrect spacer arrangement.
After assembly, inspect the characteristics that matter to the actual machine—secure mounting, alignment, free rotation, belt tracking and any drawing-controlled runout or axial position. Do not apply a generic tolerance where the equipment or order drawing defines a different requirement.
Sipariş, Numuneler ve Ticari Planlama
Minimum sipariş miktarları, ürün türüne, üretim yöntemine ve toplam sipariş değerine göre belirlenir. Standart katalog parçaları genellikle üretim miktarı minimumlarına tabidir.
Yeni müşteriler, konfigürasyon ve üretim yöntemi uygun olduğunda 1-5 adet numune talep edebilirler. Numuneler ayrı olarak fiyatlandırılır.
Farklı kasnak modelleri birleştirilebilir. Karma model siparişleri için genellikle yaklaşık 1.500 ABD doları tutarında birleşik sipariş değeri planlama noktasıdır.
Tek veya iki parçalık miktarlar yalnızca mühendislik doğrulaması veya nitelikli ücretli numune gereksinimi için değerlendirilebilir, perakende sipariş olarak kabul edilmez; birim fiyatı buna bağlı olarak daha yüksektir.
Standart parçalar: Genellikle 10-25 iş günü. Özel bileşenler: Genellikle 20-45 iş günü. Proje bazlı montajlar veya ilgili ekipmanlar: Uygulanabilir durumlarda 45-120 iş günü. Nihai süre, çizim, malzeme ve miktar incelemesinden sonra teyit edilir.
EXW, FOB, CIF ve DAP yaygın olarak mevcuttur. Uygun sevkiyatlar ve varış noktaları için FCA, CFR, CPT, CIP ve DDP görüşülebilir.
How to Prepare an RFQ for 8M-50
Send the complete belt marking, required tooth count, belt width, shaft diameter and fit, mounting method, quantity and destination. Add a dimensioned drawing or clear replacement photographs when hub projection, flange geometry, keyway, finish or inspection limits are not standard. If you are replacing an obsolete pulley, include front, rear and side measurements rather than relying on one outside-diameter value.
For related decisions, compare the 8M product family, review the HTD pulley selection guide, or see application guidance for machine-specific considerations.
8M-50 Frequently Asked Questions
Is every 8M-50 pulley interchangeable?
No. The series code narrows the pitch and width family, but tooth count, construction type, bore or bush, hub dimensions, flange arrangement and material can differ. Confirm the exact catalogue row or drawing.
Can you quote from an existing pulley?
Yes, provided the replacement information is sufficient. Send belt marking, tooth count, face width, shaft details and measurements from both sides. A drawing is preferred for nonstandard geometry.
Can small quantities be supplied?
Small paid samples may be considered for qualified engineering validation. The normal sales route is industrial production supply rather than one- or two-piece retail purchasing.
What documents should be requested with the order?
State required dimensional inspection, material documentation, marking or order-specific compliance records at RFQ stage so availability and scope can be confirmed before production.
